Audi A4, S4
Introduction
- Controls and receptions of safe operation
   Controls and devices
   Information system of the driver (FIS)
   Unlocking and car lock-out
   Illumination and review maintenance
   Seats and niches
   Heater, ventilation and air conditioner
   Automatic transmission (АТ)
   Communication and navigation
   Universal remote radio management HOME LINK
   Safety systems
   Features of operation and auxiliary systems
   Обкатка
   Trailer towage
   In case of emergency
   Car refuelling
Current leaving and service
The engine
Systems of cooling, heating and the air conditioner
Power supply systems, release and decrease in toxicity of the fulfilled gases
Systems of an electric equipment of the engine
Manual box of a gear change
Automatic transmission
Coupling, power shafts and differential
Brake system
Suspension bracket and steering
Body
Onboard electric equipment




Universal remote radio management HOME LINK

The description

Universal remote radio management HOME LINK can be programmed portable transmitters of already programmed devices.

Universal remote radio management HOME LINK gives convenient possibility, without leaving the car, to use various devices, for example, garage gate/collars of a site, safety system, house illumination etc.

Universal remote radio management HOME LINK allows to replace three various portable transmitters of corresponding devices with one (universal remote radio management). Mechanisms of garage and external gate more often concern such devices. Programming of portable transmitters on your remote radio management is carried out near a forward bumper on the right. There there is a management block.

For management possibility various devices by means of universal remote radio management HOME LINK it is necessary to program the corresponding transmitter preliminary. If after the first programming of the device do not function, the given devices should be checked up on presence of a dynamic code.

The list of compatible portable transmitters can be received by fax: 49(0) 6838 907 283 3333. More detailed information rather HOME LINK and-or compatible with HOME LINK products can be received, having called on duty-free hot line HOME LINK (0 08000466 35465 or 49(0) 6838 907 277 or visit page HOME LINK in system the Internet

Transmitter programming

Programming of universal remote radio management HOME LINK is carried out located in a sun-protection peak of the driver by keys, and also from outside a forward bumper.

From outside a sun-protection peak

Sun-protection peak of the driver

 PERFORMANCE ORDER

    Include ignition/engine does not work. Press both extreme keys of universal remote control HOME LINK , the light-emitting diode (A) (approximately in 20 seconds) yet will not start to blink. Press key HOME LINK which you wish to program. Wait, while the light-emitting diode () will start to blink. The five-minute stage of programming of module HOME LINK begins. Leave the car and become before it with an original portable transmitter of a drive of garage gate or other device on which you wish to program key HOME LINK .

From outside a forward bumper

The right party of a forward bumper

 PERFORMANCE ORDER

    Hold an original portable transmitter on removal approximately 0 - 30 sm under the right forward headlight at a bumper of your car. Press a key of inclusion of an original portable transmitter. At the included function of a portable transmitter observe of indexes of turn of the car. The positive result of programming HOME LINK proves to be true a triple blinking of system of the emergency light alarm system. In the absence of a triple blinking of lanterns repeat programming process on other removal from a bumper.

The distance between a portable transmitter and module HOME LINK located in a bumper is defined by the device which you wish to program. Probably, for programming some attempts is required.

Excess of a five-minute stage of programming proves to be true a unitary blinking of system of the emergency light alarm system. In this case it is necessary to repeat a programming stage from outside a sun-protection peak.

At programming of two other keys be guided by the above-stated description. 3 from outside a sun-protection peak it is necessary to begin with action also if programming is carried out right after programming of the first key.

If after positive programming, nevertheless, keys HOME LINK do not possible to open garage gate or other systems there is a probability of functioning of concrete system with a dynamic code. In this case programming of a dynamic code is necessary.

Programming of a dynamic code

Some devices demand additional programming of a dynamic code of universal remote radio management HOME LINK .

Identification of a dynamic code

 PERFORMANCE ORDER

    Again press and keep pressed key HOME LINK which you already programmed earlier. Observe of light-emitting diode HOME LINK (A). If the diode quickly blinks in the beginning, and in 2 seconds burns continuously it means presence of a dynamic code of the corresponding device, for example, devices for opening of garage gate. The dynamic code is programmed in the following sequence:

Inclusion of function of the mechanism of the electric motor of the device for opening of garage gate

 PERFORMANCE ORDER

    To find a key of adjustment of the mechanism of the electric motor of the device for opening of garage gate. The exact site and colour of a key depends on mark of the manufacturer of the device. Press a key of adjustment of the mechanism of the electric motor of the device for opening of garage gate. (Thus the light-emitting diode of "adjustment" of the mechanism of the electric motor), as a rule, burns. Now at your order about 30 seconds for realisation of programming of key HOME LINK located in a sun-protection peak .

Programming from outside a sun-protection peak

 PERFORMANCE ORDER

    Again press and release key HOME LINK which you already programmed earlier. For end of programming of a dynamic code again press key HOME LINK .

After programming by a key of a sun-protection peak the device for opening of garage gate should distinguish signal HOME LINK and open gate after pressing of key HOME LINK. If necessary now it is possible to program other keys.

In the presence of the assistant process of programming of a dynamic code can be simplified and accelerated. For end of process of adjustment of some devices for opening of garage gate it is necessary the third time press key HOME LINK .

In case of difficulties of programming of a dynamic code studying of the operation manual on the device for opening of garage gate / other device probably will help.

Using HOME LINK

Using the programmed devices is carried out located in a sun-protection peak of the driver by keys HOME LINK .

 PERFORMANCE ORDER

    Include ignition/engine does not work. Press programmed key HOME LINK . There is a management of the device programmed on a given key (for example, the device for opening of garage gate).

During a manipulation with command keys light-emitting diode HOME LINK burns.

Dump of programmed given keys HOME LINK

Both extreme command keys dump of all programmed data HOME LINK is possible.

 PERFORMANCE ORDER

    Include ignition/engine does not work. Press both extreme keys, the light-emitting diode yet will not start to blink. Release keys.

After dump of the data of programming of keys of universal remote radio management HOME LINK the device again is in a mode of adjustment and is ready to new programming.

Separate dump of the programmed keys is impossible.

For the safety reasons dump programming of keys HOME LINK before car sale.

Reprogramming of one key HOME LINK

There is a possibility of reprogramming of one key HOME LINK without change of the programmed positions of other keys.

From outside a sun-protection peak

 PERFORMANCE ORDER

    Press actual key HOME LINK , slowly the light-emitting diode yet will not start to blink.

From outside a forward bumper

 PERFORMANCE ORDER

    Hold an original portable transmitter of a drive of garage gate or other device on removal about 0-30 sm under the right forward headlight at a bumper of your car. The necessary distance is defined by the device which you wish to program. Press a key of inclusion of an original portable transmitter of the device for opening of garage gate or other device. At the included function of a portable transmitter observe of indexes of turn of the car. The positive result of programming HOME LINK proves to be true a triple blinking of system of the emergency light alarm system. In the absence of a triple blinking of lanterns repeat programming process on other removal from a bumper.

After a triple blinking of the emergency light alarm system there is a dump before programmed data HOME LINK: and the new device is programmed. For using the new device press programmed key HOME LINK .

For programming, some attempts probably is required. Duration of process of adjusting position of each attempt should make a minimum of 15 seconds. Only after that it is possible to pass to other position. Observe thus of lanterns of indexes of turn.