Audi A4, S4
Introduction
Controls and receptions of safe operation
Current leaving and service
The engine
Systems of cooling, heating and the air conditioner
Power supply systems, release and decrease in toxicity of the fulfilled gases
Systems of an electric equipment of the engine
Manual box of a gear change
Automatic transmission
Coupling, power shafts and differential
Brake system
Suspension bracket and steering
- Body
   The general data and security measures at carrying out кузовных works
   Cleaning and leaving
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   - The external equipment
      Installation of the forward panel in position for maintenance service
      Removal and installation of a cover of a water modular compartment
      Removal and installation of a forward bumper
      Removal and installation локера a back wing
      Removal and installation локера a forward wing
      Removal and installation of a forward wing
      Removal and installation of a back bumper
      Removal and cowl installation/adjustment
      Removal and installation of a cable of a drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and door installation
      Door adjustment
      Removal and installation of a frame of a window of a forward door
      Removal and installation стеклоподъёмника
      Removal and installation of the electric motor of a drive стеклоподъёмника
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a cover of a luggage carrier
      Removal, installation and adjustment of a cover of a luggage carrier
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Versatile person)
      Removal and installation of a door of a back (Versatile person)
      Removal and installation of the lock of a door of a back (Versatile person)
      Removal and installation of an external mirror
      Removal and installation молдингов
      Removal, installation and check сдвижной roof panels
      Removal and overlay installation сдвижной roof panels
      Check and starting position adjustment сдвижной roof panels
      Removal and sealant installation сдвижной panels
      Replacement of elastic bands of brushes of a screen wiper
      Removal and jet installation ??????????????? a windscreen
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of a cleaner of a windscreen
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets фароомывателя
      Adjustment of levers of a screen wiper
    The salon equipment
Onboard electric equipment





Removal and installation молдингов

Молдинг doors

Молдинги are pasted to a body and at their removal collapse.

Removal

 PERFORMANCE ORDER

    Heat up parts молдинги (1) and (2) hair dryer and separate them from a door.

Installation

 PERFORMANCE ORDER

    Clear a place where the lath will be pasted, gasoline, process silicone удалителем and dry.

Молдинги it is necessary to paste only at a room temperature. For this purpose the car and laths a minimum two hours prior to gluing should be placed indoors with a room temperature.

    Remove a protective film (3) with a bilaterial sticky tape (4). Insert молдинг pins into apertures on a door and paste. Heat up молдинг the hair dryer to temperature 40 С and strongly press or прокатайте.

After приклейки молдингов hold the car within four hours at a room temperature.

Молдинг the bottom beam

Removal

 PERFORMANCE ORDER

    Turn out screws (3) and put forward forward молдинг (1) back from holders.

Similarly remove back молдинг (2).

Installation

 PERFORMANCE ORDER

    Establish молдинг on the bottom beam, move forward in holders and fix screws.