6 and 8-cylinder petrol engines

The basic data

Engines have three inlet and two final valves on the cylinder. Each number of cylinders of the engine has on 2 camshafts. At engine V6 camshafts of final valves are set in motion by a gear belt, camshafts of inlet valves are set in motion by a chain from camshafts of final valves. At engine V8 four camshafts, also as well as auxiliary units, are set in motion by several chains. Privodnye chains are located from outside a flywheel (the check point party).

The block of cylinders, crankshaft and engine V6 flywheel

1 — the Cranked shaft Check axial backlash: The new: 0.07 - 0.23 mm Deterioration limit: 0.25 mm Check of a radial backlash by means of Plastigage: 0.018 - 0.045 mm Deterioration limit: 0.10 mm Attention: At check of a radial backlash do not rotate a cranked shaft. 2 — the Cover of the radical bearing 4 with dredging for a persistent washer 3 — the Bolt. Replace, 60Нм90 . For measurement of a radial backlash tighten a bolt effort no more 60Нм 4 — the Persistent washer of the radical bearing 4 5 — the Flywheel/privodnoj a disk

6 — the Bolt of a flywheel/privodnogo of a disk. Replace, (a flywheel 60Нм180 ), (приводной a disk 60Нм90 ). At отдавании use the tool 3242 for blocking of a cranked shaft 7 — Loose leaves of radical bearings. Do not mix the removed loose leaves 8 — the Tight flange with an epiploon. It is replaced in gathering. Before removal merge cooling liquid 9 — the Lining. Replace 10 — the Bolt, 10Нм 11 — the Persistent washer of the block of cylinders, the bearing 4 12 — the Bolt, 25Нм. Preliminary tighten by hand before to tighten bolts of a cover of the radical bearing 13 — the Block of cylinders 14 — the Directing plug

Basic elements of drive ГРМ of engine V6

1 — the Bolt, 55Нм 2 — Natjazhitel of a gear belt. Before removal block by means of the tool 3204 3 — the Top right cover of a gear belt 4 — the Central right cover of a gear belt 5 — the Gear belt. Before removal mark a direction of movement of a belt. Check up on deterioration. Do not bend 6 — the Top left cover of a gear belt 7, 8 — the Bolt, 25Нм 9 — the Washer 10 — the bearing Plug 11 — the Tension roller of a gear belt 12 — the Tension lever 13 — the Sealing ring 14 — the Bolt, 25Нм 15 — the Arm 16 — Connection (the thermostat case) 17 — the Water pump 18 — the Oil pump

19 — the Head of cylinders 20 — the Case сапуна картера 21 — the Block of cylinders 22 — the Bolt, 45Нм 23 — the Arm 24 — the Pallet картера 25 — the Directing roller 26 — the Bolt, 45 Nanometers 27 — the Cogwheel crankshaftа 28 — the Bolt 200Нм180 , replace 29 — Natjazhitel of a belt 30 — the Bolt, 10Нм. Establish with greasing D6 31 — a fan Pulley 32 — Bolt М8 - 25Нм, М6 - 10Нм 33 — the Cover of a gear belt 34 — the Bolt, 10Нм 35 — Dempfer крутильных fluctuations 36 — the Bolt, 25Нм

Chain drive of a cam-shaft of inlet valves. Engine V6

1 — the Top right cover of a gear belt 2 — the Central right cover of a gear belt 3 — the Top left cover of a gear belt 4 — Shestigrannaja a nut, 10Нм 5 — the Back cover of a gear belt 6 — the Elevating eye 7 — the Bolt, 25Нм 8 — the Lining of a cover of a head of cylinders. At damage replace. Before installation grease a lining surface between a cover of the bearing and a head of cylinders greasing D 454 300 A3 9 — the Cover of a head of cylinders

10 — the Lining 11 — the Cover. At damage a lining replace 12 — the Arm 13 — Shestigrannaja a nut, 10Нм. Tighten in a direction from the centre outside 14 — the Bolt of a head of cylinders. Replace 15 — the Head of cylinders. Check up planeness 16 — Maslootrazhatel 17 — the Lining of a head of cylinders (metal). Replace 18 — the Cogwheel of a cranked shaft 19 — the Tightening plate 20 — the Bolt, 55Нм

Elements of a head of cylinders. Engine V6

1 — the Double cover of bearings. Slightly grease an interfaced surface with greasing AV 174 004 01 2 — the Bolt, 10Нм 3 — Covers of bearings of a camshaft of final valves. Slightly grease interfaced surfaces of extreme (external) bearings with greasing AV 174 004 01 4 — the Camshaft of final valves. Check of a radial backlash by means of Plastigage: Palpation, no more: 0.01 mm Deterioration limit: 0.10 mm 5 — the Cap. Replace. For removal uncover the bearing. At the established cover of the bearing напрессуйте by means of the tool 3202 and a plastic hammer 6 — Covers of bearings of a camshaft of inlet valves 7 — the Camshaft of final valves 8 — a camshaft Regulator. Before removal block by means of a clamp 3366 натяжителя chains. Check up camshaft adjustment 9 — Privodnaja a chain. Before removal mark a movement direction 10 — the Bolt, 10Нм 11 — the Sealing ring. Replace 12 — the Valve 1 or 2 for adjustment of camshaft N205 or N208. Check up camshaft adjustment

13 — the Lining (rubber/metal). Replace 14 — the Segment insert. Replace 15 — the Hydraulic pusher of the valve. Do not interchange the position of pushers of different valves. Store downwards a surface of contact to a camshaft cam 16 — Crackers of the cutting lock 17 — the Holder клапанной springs 18 — Klapannaja a spring 19 — Maslootrazhatelnyj a cap 20 — the Rod of a pusher of the valve 21 — the Head of cylinders 22 — Valves 23 — the Epiploon. Slightly grease epiploon sponges 24 — Zaslonka CMP 25 — the Conic washer 26 — the Bolt, 25Нм 27 — the Gauge of position of a camshaft (CMP) 28 — the Bolt, 10Нм 29 — the Directing plug