|
Audi A4, S4 Introduction Controls and receptions of safe operation - Current leaving and service Specifications The indicator of term of approach of maintenance service The routine maintenance schedule The general information on adjustment Check of levels of liquids, the control of leaks Check of a condition of tyres and pressure in them. A designation of tyres and disks of wheels. Rotation and replacement of wheels Replacement of impellent oil and the oil filter Checks of brake system. Adjustment of a lay brake Check of fuel system Check of a condition and replacement of hoses of an impellent compartment, localisation of leaks Check of a condition of ridge belts of a streaming drive of auxiliary units Check of functioning of system of cooling and frost resistance of a cooling liquid Check of a condition of system of release of the fulfilled gases Check of level of oil of automatic transmission The visual control of a box of a gear change and the main transfer on leaks, check of level and oil addition Check of a condition a suspension bracket and steering component Check of a condition of protective covers of power shafts Check of level of a liquid of system of hydrostrengthening of a wheel Check of a central air of air Greasing of terminators of doors, cylinders of locks, cowl hook, сдвижной panels of the hatch of a roof The visual control of a seat belt and the block of a pillow of safety Check of working capacity of headlights and horn Condition check, adjustment and replacement of brushes of screen wipers Check of a condition of the battery, care it and gymnastics Replacement of the battery of emergency supply of system Telematik Replacement of an element of the filter of air of salon / the coal filter of clearing of air Replacement of a brake liquid Check and replacement of spark plugs. Check of a condition of high-voltage wires Replacement of an element of the air filter of the engine Replacement of the fuel filter Check of a condition and tension of a gear belt The engine Systems of cooling, heating and the air conditioner Power supply systems, release and decrease in toxicity of the fulfilled gases Systems of an electric equipment of the engine Manual box of a gear change Automatic transmission Coupling, power shafts and differential Brake system Suspension bracket and steering Body Onboard electric equipment |
Check of a condition and replacement of hoses of an impellent compartment, localisation of leaks
The general information Influence of heats in an impellent compartment leads to gradual failure of the rubber and plastic hoses used in various systems. It is necessary to make regularly check of hoses on presence of cracks, easing of fastening of collars, hardening of materials and signs of leaks. The information concerning hoses of system of cooling, is resulted more low, and in hoses of brake system - in Section of Check of brake system. Adjustment of a lay brake. The majority of hoses (but not all) fasten by means of collars. There, where collars are used, check up reliability of their fastening providing absence of leaks. If collars are not used, make sure that the hose in a junction with the union was not inflated and-or has not hardened, supposing leaks. If there are signs that there is a leak of any liquid, but you cannot distinguish type of a liquid or an exact origin it is necessary to leave the car for long time and to put the big piece of a paper or a rag under the car. It will help to find a place of course of a liquid, and also will help to identify a liquid on colour. But keep in mind that some leaks can be shown only at the working engine. Vacuum hoses Usually vacuum hoses especially applied in systems of decrease of toxicity of fulfilled gases, differ colour or have colour strips. Various systems demand use of hoses with various thickness of walls, thermal stability and various resistance схлопыванию. At replacement of hoses watch that the material of a new hose corresponded to a material of the old. Often unique authentic way of check of a condition of a hose is its full removal from the car. At removal more than one hose takes care of an accurate designation of hoses and unions to provide correct assemblage. At check of vacuum hoses do not forget to check up T-shaped plastic connections also. Examine them on presence of cracks which can cause leaks.
Leak in a vacuum hose means that air is sucked in in a hose (instead of leaves a hose), and it does leak very difficult for detection. For revealing of leaks of vacuum it is possible to take advantage of a small piece of a vacuum hose as a stethoscope. When the hose end will be directly over the leak place, the hissing sound will be clearly audible through a hose. Hear to all vacuum hoses and connections on presence of the characteristic hissing testifying to leak. It is necessary to avoid contact to hot and moving details as the engine at check should work. Fuel hoses
Fuel hoses usually are under pressure, therefore at their detachment be ready to that fuel will be sprayed also it it is necessary to collect.
Check up all rubber fuel hoses on presence of signs of deterioration and attritions. Pay special attention on sites of a bend and in front of unions, for example a junction of a hose with the fuel pump or the filter, cracks there can be formed. Use only high-quality fuel hoses. Never, under no circumstances do not use as fuel not reinforced vacuum hoses, transparent plastic tubes or water hoses. For fastening of fuel hoses collars of tape type are usually used. These collars weaken in due course a tension and can "jump out" at removal. At replacement of hoses replace such collars with collars of screw type. Fuel leaks precisely to define difficultly while leak does not become essential and, hence, easily visible. Fuel tends to evaporate quickly as soon as it contacts with air, especially in a hot impellent compartment. Small drops can disappear before you can define a leak place. If you suspect that leak of fuel in the field of an impellent compartment then cool the engine takes place and start it, while it cold, at an open cowl. Metal subjects are compressed at cooling, and rubber hoses tend to be weakened, so any leaks will be more obvious, while the engine heats up at start from a cold condition. Metal lines Between the fuel pump and system of injection of fuel sections of metal tubes are often inserted. Carefully check these tubes on presence of dents, twisting or cracks. If it is necessary to replace section of a metal line, use only seamless steel tubes, since copper and aluminium tubes are insufficiently strong to resist to the vibrations caused by work of the engine. Check metal brake lines in places of their connection with the main cylinder and with a regulator of pressure or ABS (if it is available) on presence of cracks or weakened штуцерных connections. Any signs of leak of a brake liquid demand immediate careful survey of all brake system. Hoses of system of hydrostrengthening of a wheel Check up hoses of system of hydrostrengthening of a wheel on presence of signs of leak of the liquid, weakened штуцерных connections and the worn out collars. It is necessary to replace proceeding hoses and the worn out collars. Hoses of system of cooling Leaks in cooling system are usually found out on white or colours of a rust to a touch in the area adjoining leak. Carefully check up a radiator and hoses of a cooling liquid on инами, ruptures and ageing signs. Cracks are easier for finding out if to press a hose. Will pay special attention on collars which attach hoses to elements of system of cooling. Collars of fastening of a hose which have been strongly tightened, can cause rupture or a hose puncture, leaks in cooling system will be result of that. Examine all hoses and surfaces of connection of hoses about leaks. If any problems of similar character with leaks replace this component or a lining are found out. |
|