|
Audi A4, S4 Introduction - Controls and receptions of safe operation Controls and devices Information system of the driver (FIS) Unlocking and car lock-out Illumination and review maintenance Seats and niches Heater, ventilation and air conditioner Automatic transmission (АТ) Communication and navigation Universal remote radio management HOME LINK Safety systems Features of operation and auxiliary systems Обкатка Trailer towage In case of emergency Car refuelling Current leaving and service The engine Systems of cooling, heating and the air conditioner Power supply systems, release and decrease in toxicity of the fulfilled gases Systems of an electric equipment of the engine Manual box of a gear change Automatic transmission Coupling, power shafts and differential Brake system Suspension bracket and steering Body Onboard electric equipment |
Controls and devices
The arrangement of some controls of cars with a right-hand steering differs from shown on an illustration. However the symbols used for their designation, correspond to symbols of cars with a link sided steering. The central console
The arrangement of some controls of cars with a right-hand steering differs from shown on an illustration. However the symbols used for their designation, correspond to symbols of cars with link sided management. In case of a factory complete set of the car the system of navigation Audi plus and radio system Audi symphony on them applies the corresponding operation manual. In system of navigation Audi plus functions of radio, a player компакт disks and телевизора* are built in. Control panel The control panel serves the driver as car information centre.
The index of temperature of a cooling liquid The index of temperature of a cooling liquid works only at the included ignition. In order to avoid engine damages take into consideration following instructions concerning temperature modes.Interval of temperatures of the cold engine If the arrow still is in the left part of a scale it means that the engine yet has not reached working temperature. Avoid the raised turns, full gas and considerable loading of the engine.Working temperature The engine has reached working temperature if at a normal mode of movement of the marksman of the index of temperature is in limits of an average part of a scale. At considerable loading of the engine and a heat of external air of the marksman can depart and further to the right on a scale. It should not become an occasion to alarm while on the control panel display the alarm symbol will not light up The blinking of an alarm symbol on the display testifies to falling of level of a cooling liquid or its overheat, the Information system of the driver (FIS) see. Additional headlights and others interfering a supply of cooling air hinged components worsen effect of cooling of a cooling liquid. At high external temperature and considerable loading of the engine in this case there is a danger of an overheat of the engine! One of problems of a forward spoiler during movement is correct distribution of cooling air. At spoiler damage the cooling effect worsens and there is a danger of an overheat of the engine! Take advantage of the qualified help.
Tachometre The tachometre shows frequency of rotation crankshaftа the engine. At frequency of rotation less than 1500 turns in a minute it is necessary to be switched to the following hill-climbing gear. The beginning of red sector of a scale corresponds for all transfers to a range of the maximum turns, admissible is short-term for обкатанного and the heated-up engine. It is necessary to be switched to the raised transfer, to establish the selector lever in position D or to reduce gas till the moment of achievement by an arrow of the given sector of a scale. Short-term calling of an arrow of a tachometre on red sector of a scale is supposed only - there is a danger of damage of the engine! The beginning of a red scale depends on an engine variant. Preliminary switching on the raised transfers will help you to save fuel and to lower operational noise!
Digital watch with date indication — A digital watch The car is completed with a quartz watch or radio hours. Installation of hours PERFORMANCE ORDER Installation of minutes PERFORMANCE ORDER Installation of calendar date PERFORMANCE ORDER Deenergizing of calendar date PERFORMANCE ORDER Call of calendar date PERFORMANCE ORDER The termination of a blinking of indication after button pressing means end of process of installation and time programming / calendar date. Button SNESK pressing, at the switched off ignition it is possible to include for some seconds a digital watch with indication of date and the run counter.
Radio hours In a mode a radio-controlled quartz watch on the display panel there is a symbol of reception of radio of the information (radio a tower with dispersing waves). In the given mode manual change of indication of minutes and date is impossible. In various time zones it is necessary to change indication of hours accordingly manually. In the absence of a corresponding radio signal within three days, hours are automatically switched in a mode "quartz watch". Indication of a symbol of reception of radio of the information Thus disappears. In need of new installation of time and calendar date address to subsection the Digital watch with date indication.
Illumination of devices PERFORMANCE ORDER The phototransistor established in a control panel regulates illumination of devices (illumination of arrows and scales), illumination of the central console and illumination of displays. At switched off light and the included ignition devices (arrows and scales) are shined. With fall of brightness of a surrounding background brightness of illumination of devices automatically decreases. At insignificant surrounding light illumination in general is disconnected. The given function serves the driver as a reminder of timely inclusion of a passing light at fall of brightness of a surrounding background.
Speedometer, the counter of the general run and run measuring instrument Speedometer The speedometer shows speed. Control panel fragment: the counter and a run measuring instrument, button CHECK Run indication is deduced in kilometres (km). In some updatings indication is deduced in miles. The counter of the general run (is below) Registers the general run of the car in kilometres or miles. Run measuring instrument (is from above) Registers run from the moment of last dump of its indication. He allows to measure certain pieces of run. The price of division of a measuring instrument makes 100 m or 1/10 miles. Dump (installation of zero value) is carried out by pressing of the button of dump. Display of faults About malfunction presence in a control panel indication dEF on the display of a measuring instrument of run signals.
The index of a stock of fuel The index works only at the included ignition. Capacity of a fuel tank is resulted in Specifications. If the arrow has reached a reserve field on the control panel display, the Information system of the driver (FIS) see the symbol lights up Never develop fuel completely! Irregular giving of fuel can lead to faults in ignition system. As a result not burnt down fuel will get to system of release of the fulfilled gases. It can lead to an overheat and damage catalytic the converter
Button SNESK Button SNESK functional purpose: Inclusion of indication of a digital watch, the counter and run measuring instrument Button SNESK pressing, at the switched off ignition, for some seconds run displays join the display of a digital watch, with date indication, and. Inclusion of function of the monitoring system of malfunctions of the car (AutochekControl) At the included ignition and during movement the system of the automatic control of malfunctions, see Information system of the driver (FIS) continuously supervises certain functions and a technical condition of systems of the car. At the included ignition function of the monitoring system of malfunctions can be included also button SNESK pressing. Check of work of system can be carried out both at muffled, and at the working engine and at speed no more than 5 km/h. Conclusion to indication of instructions to the driver At a blinking on the display of any symbol of 1st degree of a priority, the Information system of the driver (FIS) see or at occurrence of the indication informing on malfunction of function of lamps, the Information system of the driver (FIS) see, short-term pressing of button SNESK it is possible to include again illumination of the corresponding instruction to the driver. For example: Motor abstellen, Olstand prufen (to muffle the engine to check up oil level). Display indication dies away approximately in 5 seconds. The alarm system of excess of speed Pressing of button SNESK during movement it is possible to program threshold value of degree of the prevention of 1 device of the alarm system of excess of speed, the Information system of the driver (FIS), Degree of the prevention 1 see: function. Threshold value of degree of the prevention of 2* devices of the alarm system of excess of speed, see Information system of the driver (FIS), Degree of the prevention 2: function is programmed only at the switched off ignition.
Indication of term of maintenance service Indication of term of maintenance service reminds of the next servicing. Control panel fragment: indication of term of maintenance service Maintenance service indication Short-term pressing of the button (1) at the included ignition on indication deduces quantity of kilometres before forthcoming servicing. The indication conclusion is possible both at muffled, and at the working engine and at speed no more than 5 km/h. Indication of quantity of kilometres before maintenance service is staticized each time after ignition inclusion - the first time through 500 km after dump. On indication of the display of the new car/car after carrying out of maintenance service in the first 500 km of run will be, message SERVICE IN — — KM — TAGEN is deduced. It extends also on cars with LongLifeservice. Reminder on maintenance service When before forthcoming servicing remains 2000 and less kilometres, at ignition inclusion on the display indication is deduced: SERVICE IN 2000 km—TAGEN Later 5 seconds the display are switched to a normal mode of indication. Indication of quantity of kilometres before servicing is staticized each time after ignition inclusion, up to approach of term of carrying out of maintenance service. Approach of term of maintenance service At approach of term of passage of the next maintenance service it is direct after ignition inclusion on the display indication SERVICE is deduced!. Later 5 seconds the display are switched to a normal mode of indication. Dump in position of new readout of indication Switch off ignition. At the pressed button (1) include ignition. On the display appears one or the other messages: SERVICE IN — — KM or SERVICE. Press the button of dump (2) before occurrence on the indication display SERVICE IN — — KM — TAGEN or SERVICE!. If do not press the button of dump within 5 seconds, the display is switched to a normal mode of indication. Dump indication on new readout only after maintenance service carrying out. Otherwise it will not represent the facts. At an accumulator detachment the given indications of term of maintenance service remain. In the presence of malfunction of 1st degree of a priority (a red symbol) the call of indication of quantity of kilometres before maintenance service is impossible.
The dump button The dump button 0.0, (2) has following appointment: Dump of indications of a measuring instrument of run Installation of zero value of a measuring instrument of r | ||||||||||||||||||||||||||||||||||||||||||||