Audi A4, S4
Introduction
Controls and receptions of safe operation
Current leaving and service
The engine
Systems of cooling, heating and the air conditioner
Power supply systems, release and decrease in toxicity of the fulfilled gases
Systems of an electric equipment of the engine
Manual box of a gear change
Automatic transmission
Coupling, power shafts and differential
Brake system
Suspension bracket and steering
- Body
   The general data and security measures at carrying out кузовных works
   Cleaning and leaving
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   - The external equipment
      Installation of the forward panel in position for maintenance service
      Removal and installation of a cover of a water modular compartment
      Removal and installation of a forward bumper
      Removal and installation локера a back wing
      Removal and installation локера a forward wing
      Removal and installation of a forward wing
      Removal and installation of a back bumper
      Removal and cowl installation/adjustment
      Removal and installation of a cable of a drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and door installation
      Door adjustment
      Removal and installation of a frame of a window of a forward door
      Removal and installation стеклоподъёмника
      Removal and installation of the electric motor of a drive стеклоподъёмника
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a cover of a luggage carrier
      Removal, installation and adjustment of a cover of a luggage carrier
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Versatile person)
      Removal and installation of a door of a back (Versatile person)
      Removal and installation of the lock of a door of a back (Versatile person)
      Removal and installation of an external mirror
      Removal and installation молдингов
      Removal, installation and check сдвижной roof panels
      Removal and overlay installation сдвижной roof panels
      Check and starting position adjustment сдвижной roof panels
      Removal and sealant installation сдвижной panels
      Replacement of elastic bands of brushes of a screen wiper
      Removal and jet installation ??????????????? a windscreen
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of a cleaner of a windscreen
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets фароомывателя
      Adjustment of levers of a screen wiper
    The salon equipment
Onboard electric equipment





Removal and jet installation ??????????????? a windscreen

Removal

 PERFORMANCE ORDER

    Open a cowl.

Jets ??????????????? are established from the bottom party of a cowl.

    By means of a plastic wedge, for example, HAZET 1965-20 take away the basis of a jet from a cowl.
    Remove a water hose from a jet.
    If necessary, disunite a socket of heating of a jet.

Installation

 PERFORMANCE ORDER

    Installation is carried out in sequence, return to removal. Thus the water hose should be fixed distinctly on a jet of washing of a windscreen. Close a cowl and check up working capacity of jets, if necessary, adjust.

Adjustment

 PERFORMANCE ORDER

    The direction of a stream of jets can be adjusted by means of the special tool 3125A or HAZET 4850-1. For this purpose insert into a jet оправку and put on glass a label.

Do not apply in quality оправки a needle since in this case it is possible to damage water channels of jets.

    With felt-tip pen mark on a windscreen of 4 points to which the water stream should get.

    And — From 250 to 275 mm (a cabriolet: 340 mm)
    b — From 465 to 490 mm (a cabriolet: 500 mm)
    c — From 270 to 415 mm (a cabriolet: 450 mm)
    d — From 140 to 225 mm (a cabriolet: 280 mm)

The resulted adjusting sizes are established from an external edge of glass and represent anticipatory values for the moving car, i.e. in a motionless condition jets give a stream a little displaced upward.

    If the stream is not regulated or is non-uniform, it is necessary to replace a jet.
    If it is necessary, remove a jet for its clearing and blow compressed air through the union for a hose.

Do not blow a jet against a liquid direction.